=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2016.01.27 15:35:15 =~=~=~=~=~=~=~=~=~=~=~= U-Boot SPL 2015.07 (Jan 14 2016 - 17:58:27) U-Boot 2015.07-00247-g741fda0-dirty (Jan 14 2016 - 17:44:54 +0800) I2C: ready DRAM: 1 GiB Reset Source: Power-on reset has occurred. PMIC: TPS65218 MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1, OMAP SD/MMC: 2 SF: Detected MX25U3235F with page size 256 Bytes, erase size 4 KiB, total 4 MiB *** Warning - bad CRC, using default environment Board: SMARC-T437X Rev.00A0 BOOT_SEL Detected: ON OFF OFF, Load zImage from Carrier SD Card... Net: not set. Validating first E-fuse MAC cpsw, usb_ether Hit any key to stop autoboot: 1  0 switch to partitions #0, OK mmc0 is current device SD/MMC found on device 0 reading uEnv.txt 1882 bytes read in 12 ms (152.3 KiB/s) Loaded environment from uEnv.txt Importing environment from mmc ... Running uenvcmd ... reading zImage 3061440 bytes read in 139 ms (21 MiB/s) reading /dtbs/am437x-smarct437x.dtb 45323 bytes read in 8 ms (5.4 MiB/s) Kernel image @ 0x82000000 [ 0x000000 - 0x2eb6c0 ] ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 8800e10a Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.1.13-17762-g9a2fcea-dirty (linux@developer) (gcc version 4.9.3 20150413 (prerelease) (Linaro GCC 4.9-2015.05) ) #1 PREEMPT Wed Jan 27 14:51:33 CST 2016 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: TI AM437x SMARCT437X [ 0.000000] cma: Reserved 24 MiB at 0xbe800000 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM437x ES1.2 (sgx neon ) [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260434 [ 0.000000] Kernel command line: console=ttyS4,115200n8 root=/dev/mmcblk1p2 ro rootfstype=ext4 rootwait fixrtc consoleblank=0 mem=1024M [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1004920K/1048576K available (5847K kernel code, 225K rwdata, 2204K rodata, 264K init, 238K bss, 19080K reserved, 24576K cma-reserved, 245760K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc07e5024 (8053 kB) [ 0.000000] .init : 0xc07e6000 - 0xc0828000 ( 264 kB) [ 0.000000] .data : 0xc0828000 - 0xc08606e8 ( 226 kB) [ 0.000000] .bss : 0xc0863000 - 0xc089ebf8 ( 239 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Additional per-CPU info printed with stalls. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] L2C: platform modifies aux control register: 0x0e030000 -> 0x3e430000 [ 0.000000] L2C: DT/platform modifies aux control register: 0x0e030000 -> 0x3e430000 [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] OMAP L2C310: ROM does not support power control setting [ 0.000000] L2C-310 ID prefetch enabled, offset 1 lines [ 0.000000] L2C-310 dynamic clock gating disabled, standby mode disabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 256 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c9, AUX_CTRL 0x7e430000 [ 0.000000] OMAP clockevent source: timer2 at 24000000 Hz [ 0.000012] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000027] clocksource timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000036] OMAP clocksource: timer1 at 24000000 Hz [ 0.000170] Console: colour dummy device 80x30 [ 0.000202] Calibrating delay loop... 1993.93 BogoMIPS (lpj=9969664) [ 0.059296] pid_max: default: 32768 minimum: 301 [ 0.059392] Security Framework initialized [ 0.059431] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.059440] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.060082] Initializing cgroup subsys blkio [ 0.060105] Initializing cgroup subsys memory [ 0.060151] Initializing cgroup subsys devices [ 0.060165] Initializing cgroup subsys freezer [ 0.060177] Initializing cgroup subsys perf_event [ 0.060201] CPU: Testing write buffer coherency: ok [ 0.060551] Setting up static identity map for 0x80008200 - 0x80008270 [ 0.062024] devtmpfs: initialized [ 0.071107] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.083072] omap_hwmod: tptc0 using broken dt data from edma [ 0.083192] omap_hwmod: tptc1 using broken dt data from edma [ 0.083292] omap_hwmod: tptc2 using broken dt data from edma [ 0.129042] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.130777] pinctrl core: initialized pinctrl subsystem [ 0.131840] NET: Registered protocol family 16 [ 0.133131] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.159340] cpuidle: using governor ladder [ 0.189332] cpuidle: using governor menu [ 0.190683] omap_l3_noc 44000000.ocp: L3 debug error: target 8 mod:0 (unclearable) [ 0.190736] omap_l3_noc 44000000.ocp: L3 application error: target 8 mod:0 (unclearable) [ 0.193902] OMAP GPIO hardware version 0.1 [ 0.203371] No ATAGs? [ 0.203405] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.203414] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.235747] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver [ 0.238930] SCSI subsystem initialized [ 0.239601] omap_i2c 44e0b000.i2c: could not find pctldev for node /ocp/l4_wkup@44c00000/scm@210000/pinmux@800/i2c0_pins, deferring probe [ 0.239648] omap_i2c 4802a000.i2c: could not find pctldev for node /ocp/l4_wkup@44c00000/scm@210000/pinmux@800/i2c1_pins, deferring probe [ 0.239676] omap_i2c 4819c000.i2c: could not find pctldev for node /ocp/l4_wkup@44c00000/scm@210000/pinmux@800/i2c2_pins, deferring probe [ 0.239810] pps_core: LinuxPPS API ver. 1 registered [ 0.239817] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.239843] PTP clock support registered [ 0.240487] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400 [ 0.240725] Advanced Linux Sound Architecture Driver Initialized. [ 0.241413] Switched to clocksource timer1 [ 0.249423] NET: Registered protocol family 2 [ 0.250068] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.250140] TCP bind hash table entries: 8192 (order: 3, 32768 bytes) [ 0.250214] TCP: Hash tables configured (established 8192 bind 8192) [ 0.250361] UDP hash table entries: 512 (order: 1, 8192 bytes) [ 0.250383] UDP-Lite hash table entries: 512 (order: 1, 8192 bytes) [ 0.250569] NET: Registered protocol family 1 [ 0.250896] RPC: Registered named UNIX socket transport module. [ 0.250907] RPC: Registered udp transport module. [ 0.250912] RPC: Registered tcp transport module. [ 0.250917] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.252970] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.253049] audit: initializing netlink subsys (disabled) [ 0.253100] audit: type=2000 audit(0.240:1): initialized [ 0.258147] VFS: Disk quotas dquot_6.6.0 [ 0.258318] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.259931] NFS: Registering the id_resolver key type [ 0.259984] Key type id_resolver registered [ 0.259990] Key type id_legacy registered [ 0.260051] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.262379] NET: Registered protocol family 38 [ 0.262472] bounce: pool size: 64 pages [ 0.262485] io scheduler noop registered [ 0.262495] io scheduler deadline registered [ 0.262551] io scheduler cfq registered (default) [ 0.264424] pinctrl-single 44e10800.pinmux: 199 pins at pa f9e10800 size 796 [ 0.266265] backlight supply power not found, using dummy regulator [ 0.267790] 4832a000.dss supply vdda_video not found, using dummy regulator [ 0.267895] OMAP DSS rev 2.0 [ 0.268216] omapdss_dss 4832a000.dss: bound 4832a400.dispc (ops dispc_component_ops) [ 0.269648] wkup_m3_ipc 44e11324.wkup_m3_ipc: could not get rproc handle [ 0.314531] Serial: 8250/16550 driver, 10 ports, IRQ sharing enabled [ 0.317444] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 25, base_baud = 3000000) is a 8250 [ 0.318343] 48024000.serial: ttyS2 at MMIO 0x48024000 (irq = 26, base_baud = 3000000) is a 8250 [ 0.319200] 481a6000.serial: ttyS3 at MMIO 0x481a6000 (irq = 27, base_baud = 3000000) is a 8250 [ 0.320020] console [ttyS4] disabled [ 0.320081] 481a8000.serial: ttyS4 at MMIO 0x481a8000 (irq = 28, base_baud = 3000000) is a 8250 [ 1.068283] console [ttyS4] enabled [ 1.072783] [drm] Initialized drm 1.1.0 20060810 [ 1.087297] brd: module loaded [ 1.095025] loop: module loaded [ 1.099079] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.107274] m25p80 spi1.0: mx25u3235f (4096 Kbytes) [ 1.112338] 3 ofpart partitions found on MTD device spi1.0 [ 1.117847] Creating 3 MTD partitions on "spi1.0": [ 1.122687] 0x000000000000-0x000000100000 : "U-Boot" [ 1.128511] 0x000000100000-0x000000180000 : "U-Boot Environment" [ 1.135319] 0x000000180000-0x000000380000 : "Flattened Device Tree" [ 1.145167] CAN device driver interface [ 1.211467] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6 [ 1.217601] davinci_mdio 4a101000.mdio: detected phy mask ffffff3f [ 1.225169] libphy: 4a101000.mdio: probed [ 1.229213] davinci_mdio 4a101000.mdio: phy[6]: device 4a101000.mdio:06, driver Atheros 8035 ethernet [ 1.238566] davinci_mdio 4a101000.mdio: phy[7]: device 4a101000.mdio:07, driver Atheros 8035 ethernet [ 1.248502] cpsw 4a100000.ethernet: Detected MACID = c4:be:84:cc:77:95 [ 1.255913] cpsw 4a100000.ethernet: cpsw: Detected MACID = c4:be:84:cc:77:97 [ 1.264351] mousedev: PS/2 mouse device common for all mice [ 1.270199] i2c /dev entries driver [ 1.274730] omap_hsmmc 48060000.mmc: Got CD GPIO [ 1.341732] ledtrig-cpu: registered to indicate activity on CPUs [ 1.349221] omap-aes 53501000.aes: OMAP AES hw accel rev: 0.1 [ 1.358265] omap-des 53701000.des: OMAP DES hw accel rev: 0.33 [ 1.365416] omap-sham 53100000.sham: hw accel on OMAP rev 0.0 [ 1.373419] remoteproc0: wkup_m3 is available [ 1.377892] remoteproc0: Note: remoteproc is still under development and considered experimental. [ 1.387116] remoteproc0: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn't yet guaranteed. [ 1.403610] oprofile: no performance counters [ 1.408102] oprofile: using timer interrupt. [ 1.412840] Initializing XFRM netlink socket [ 1.417176] NET: Registered protocol family 17 [ 1.421804] NET: Registered protocol family 15 [ 1.426305] can: controller area network core (rev 20120528 abi 9) [ 1.432649] NET: Registered protocol family 29 [ 1.437246] Key type dns_resolver registered [ 1.441807] omap_voltage_late_init: Voltage driver support not added [ 1.449211] PM: no-rtc available, rtc-only mode disabled. [ 1.454929] ThumbEE CPU extension supported. [ 1.459284] mmc0: MAN_BKOPS_EN bit is not set [ 1.463740] Registering SWP/SWPB emulation handler [ 1.470376] mmc0: new high speed MMC card at address 0001 [ 1.476316] omapdrm omapdrm.0: DMM not available, disable DMM support [ 1.483291] mmcblk0: mmc0:0001 4YMD3R 3.64 GiB [ 1.488843] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 1.495631] mmcblk0boot0: mmc0:0001 4YMD3R partition 1 4.00 MiB [ 1.501786] [drm] No driver support for vblank timestamp query. [ 1.511513] mmcblk0boot1: mmc0:0001 4YMD3R partition 2 4.00 MiB [ 1.518474] mmcblk0: p1 p2 [ 1.564111] Console: switching to colour frame buffer device 100x30 [ 1.587742] omapdrm omapdrm.0: fb0: omapdrm frame buffer device [ 1.593701] omapdrm omapdrm.0: registered panic notifier [ 1.621493] [drm] Initialized omapdrm 1.0.0 20110917 on minor 0 [ 1.628687] omap_i2c 44e0b000.i2c: bus 0 rev0.12 at 100 kHz [ 1.673783] rtc rtc0: invalid alarm value: 1900-1-29 1193022:34:16 [ 1.680246] rtc-s35390a 1-0030: rtc core: registered rtc-s35390a as rtc0 [ 1.687227] at24 1-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 1.694331] at24 1-0057: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 1.702309] sgtl5000 1-000a: sgtl5000 revision 0x11 [ 1.726233] omap_i2c 4802a000.i2c: bus 1 rev0.12 at 100 kHz [ 1.732960] at24 2-0076: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 1.739894] omap_i2c 4819c000.i2c: bus 2 rev0.12 at 100 kHz [ 1.746608] omap_hsmmc 48060000.mmc: Got CD GPIO [ 1.751498] remoteproc0: powering up wkup_m3 [ 1.755884] remoteproc0: Booting fw image am335x-pm-firmware.elf, size 219767 [ 1.764314] remoteproc0: remote processor wkup_m3 is now up [ 1.770014] wkup_m3_ipc 44e11324.wkup_m3_ipc: CM3 Firmware Version = 0x191 [ 1.802604] sgtl5000 1-000a: Using internal LDO instead of VDDD [ 1.820596] asoc-simple-card sound@0: sgtl5000 <-> 4803c000.mcasp mapping ok [ 1.827844] asoc-simple-card sound@0: ASoC: no source widget found for HPLOUT [ 1.835067] asoc-simple-card sound@0: ASoC: Failed to add route HPLOUT -> direct -> Headphone Jack [ 1.844104] asoc-simple-card sound@0: ASoC: no source widget found for HPROUT [ 1.851284] asoc-simple-card sound@0: ASoC: Failed to add route HPROUT -> direct -> Headphone Jack [ 1.860296] asoc-simple-card sound@0: ASoC: no sink widget found for LINE1L [ 1.867310] asoc-simple-card sound@0: ASoC: Failed to add route Line In -> direct -> LINE1L [ 1.875724] asoc-simple-card sound@0: ASoC: no sink widget found for LINE1R [ 1.882741] asoc-simple-card sound@0: ASoC: Failed to add route Line In -> direct -> LINE1R [ 1.893220] rtc-s35390a 1-0030: setting system clock to 2016-01-27 07:35:22 UTC (1453880122) [ 1.905607] ALSA device list: [ 1.908692] mmc1: host does not support reading read-only switch, assuming write-enable [ 1.916802] #0: SMARCT437X SOUND CARD [ 1.921583] Waiting for root device /dev/mmcblk1p2... [ 1.932406] mmc1: new high speed SDHC card at address aaaa [ 1.938423] mmcblk1: mmc1:aaaa SS08G 7.40 GiB [ 1.947528] mmcblk1: p1 p2 [ 2.050735] EXT4-fs (mmcblk1p2): mounted filesystem with ordered data mode. Opts: (null) [ 2.059032] VFS: Mounted root (ext4 filesystem) readonly on device 179:26. [ 2.074004] devtmpfs: mounted [ 2.077457] Freeing unused kernel memory: 264K (c07e6000 - c0828000) Mount failed for selinuxfs on /sys/fs/selinux: No such file or directory [ 2.393819] random: init urandom read with 18 bits of entropy available [ 2.599784] init: plymouth-upstart-bridge main process (86) terminated with status 1 [ 2.621201] init: plymouth-upstart-bridge main process ended, respawning [ 2.732043] init: ureadahead main process (89) terminated with status 5 [ 2.740956] init: plymouth-upstart-bridge main process (96) terminated with status 1 [ 2.750008] init: plymouth-upstart-bridge main process ended, respawning [ 3.083321] init: mounted-proc main process (112) terminated with status 1 * Starting Mount filesystems on boot[ OK ] * Stopping Send an event to indicate plymouth is up[ OK ] * Starting Populate /dev filesystem[ OK ] * Stopping Populate /dev filesystem[ OK ] * Starting Populate and link to /run filesystem[ OK ] * Stopping Populate and link to /run filesystem[ OK ] * Stopping Track if upstart is running in a container[ OK ] * Starting Initialize or finalize resolvconf[ OK ] * Starting set console keymap[ OK ] * Starting Signal sysvinit that virtual filesystems are mounted[ OK ] * Starting Signal sysvinit that virtual filesystems are mounted[ OK ] * Starting Bridge udev events into upstart[ OK ] * Stopping set console keymap[ OK ] * Starting Signal sysvinit that remote filesystems are mounted[ OK ] * Starting device node and kernel event manager[ OK ] * Starting load modules from /etc/modules[ OK ] * Starting cold plug devices[ OK ] * Starting log initial device creation[ OK ] * Stopping load modules from /etc/modules[ OK ] * Starting Signal sysvinit that the rootfs is mounted[ OK ] * Starting configure network device security[ OK ] * Starting configure network device security[ OK ] * Starting set console font[ OK ] * Starting configure network device[ OK ] * Stopping set console font[ OK ] * Starting userspace bootsplash[ OK ] * Stopping userspace bootsplash[ OK ] * Starting Send an event to indicate plymouth is up[ OK ] * Starting Clean /tmp directory[ OK ] * Stopping Send an event to indicate plymouth is up[ OK ] * Stopping Clean /tmp directory[ OK ] * Starting Signal sysvinit that local filesystems are mounted[ OK ] * Starting configure network device security[ OK ] * Stopping Mount filesystems on boot[ OK ] * Starting flush early job output to logs[ OK ] * Starting D-Bus system message bus[ OK ] * Stopping flush early job output to logs[ OK ] Waiting for network configuration... Waiting up to 60 more seconds for network configuration... Booting system without full network configuration... * Starting Mount network filesystems[ OK ] * Starting Failsafe Boot Delay[ OK ] * Starting system logging daemon[ OK ] * Stopping Mount network filesystems[ OK ] * Starting configure network device[ OK ] * Stopping Failsafe Boot Delay[ OK ] * Starting System V initialisation compatibility[ OK ] * Stopping System V initialisation compatibility[ OK ] * Stopping cold plug devices[ OK ] * Loading cpufreq kernel modules...  * Starting System V runlevel compatibility[ OK ] * Starting regular background program processing daemon[ OK ] * Starting ACPI daemon[ OK ] * Starting save kernel messages[ OK ] * Starting configure network device security[ OK ] [ OK ] * Stopping log initial device creation[ OK ] * Starting OpenSSH server[ OK ] * Stopping save kernel messages[ OK ] * CPU0...  * CPUFreq Utilities: Setting ondemand CPUFreq governor...  [ OK ] udhcpd: Disabled. Edit /etc/default/udhcpd to enable it. * Starting save udev log and update rules[ OK ] * Stopping save udev log and update rules[ OK ] * Starting configure virtual network devices[ OK ] AH00557: apache2: apr_sockaddr_info_get() failed for arm AH00558: apache2: Could not reliably determine the server's fully qualified domain name, using 127.0.0.1. Set the 'ServerName' directive globally to suppress this message * * Stopping System V runlevel compatibility[ OK ] Ubuntu 14.04.1 LTS arm ttyS4 arm login: root Password: Last login: Mon Jul 7 16:59:10 UTC 2014 on ttyS4 Welcome to Ubuntu 14.04.1 LTS (GNU/Linux 4.1.13-17762-g9a2fcea-dirty armv7l) * Documentation: https://help.ubuntu.com/ root@arm:~#