U-Boot SPL 2013.10-00120-g183acb7-dirty (Apr 12 2014 - 03:25:51) reading args spl: error reading image args, err - -1 reading u-boot.img reading u-boot.img U-Boot 2013.10-00120-g183acb7-dirty (Apr 12 2014 - 03:25:51) I2C: ready DRAM: 512 MiB WARNING: Caches not enabled MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Using default environment Net: not set. Validating first E-fuse MAC cpsw, usb_ether Hit any key to stop autoboot: 1  0 gpio: pin 51 (gpio 51) value is 1 mmc0 is current device gpio: pin 54 (gpio 54) value is 1 SD/MMC found on device 0 reading uEnv.txt 442 bytes read in 3 ms (143.6 KiB/s) Importing environment from mmc ... gpio: pin 7 (gpio 7) value is 1 Checking if uenvcmd is set ... Running uenvcmd ... reading zImage 3300408 bytes read in 363 ms (8.7 MiB/s) ## Error: "loadinitrd" not defined Booting from mmc ... Kernel image @ 0x80200000 [ 0x000000 - 0x325c38 ] Starting kernel ... [ 0.000000] Linux version 3.2.0-g2887c5a (eric@developer) (gcc version 4.7.3 20130328 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.04-20130415 - Linaro GCC 2013.04) ) #1 Wed Apr 16 19:34:49 CST 2014 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: smarct335xevm [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] AM335X ES2.1 (neon ) [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttyO3,115200n8 consoleblank=0 mem=512M root=/dev/mmcblk0p2 rw rootfstype=ext4 rootwait fixrtc [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 512MB = 512MB total [ 0.000000] Memory: 512976k/512976k available, 11312k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc05ce000 (5912 kB) [ 0.000000] .init : 0xc05ce000 - 0xc0609000 ( 236 kB) [ 0.000000] .data : 0xc060a000 - 0xc066f228 ( 405 kB) [ 0.000000] .bss : 0xc066f24c - 0xc069dfa4 ( 188 kB) [ 0.000000] NR_IRQS:396 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts [ 0.000000] Total of 128 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: GPTIMER2 at 24000000 Hz [ 0.000000] omap_dm_timer_switch_src: Switching to HW default clocksource(sys_clkin_ck) for timer1, this may impact timekeeping in low power state [ 0.000000] OMAP clocksource: GPTIMER1 at 24000000 Hz [ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms [ 0.000000] Console: colour dummy device 80x30 [ 0.000203] Calibrating delay loop... 597.60 BogoMIPS (lpj=2988032) [ 0.056734] pid_max: default: 32768 minimum: 301 [ 0.056879] Security Framework initialized [ 0.056981] Mount-cache hash table entries: 512 [ 0.057383] CPU: Testing write buffer coherency: ok [ 0.078456] omap_hwmod: gfx: failed to hardreset [ 0.094944] omap_hwmod: pruss: failed to hardreset [ 0.096140] print_constraints: dummy: [ 0.096538] NET: Registered protocol family 16 [ 0.098968] OMAP GPIO hardware version 0.1 [ 0.101944] omap_mux_init: Add partition: #1: core, flags: 0 [ 0.104109] omap_i2c.1: alias fck already exists [ 0.105085] omap2_mcspi.1: alias fck already exists [ 0.105343] omap2_mcspi.2: alias fck already exists [ 0.106421] edma.0: alias fck already exists [ 0.106445] edma.0: alias fck already exists [ 0.106466] edma.0: alias fck already exists [ 0.138451] bio: create slab at 0 [ 0.140957] SCSI subsystem initialized [ 0.142802] usbcore: registered new interface driver usbfs [ 0.143161] usbcore: registered new interface driver hub [ 0.143388] usbcore: registered new device driver usb [ 0.143704] registerd cppi-dma Intr @ IRQ 17 [ 0.143719] Cppi41 Init Done Qmgr-base(e087a000) dma-base(e0878000) [ 0.143731] Cppi41 Init Done [ 0.143761] musb-ti81xx musb-ti81xx: musb0, board_mode=0x13, plat_mode=0x3 [ 0.144078] musb-ti81xx musb-ti81xx: musb1, board_mode=0x13, plat_mode=0x1 [ 0.145372] omap_i2c omap_i2c.1: bus 1 rev2.4.0 at 100 kHz [ 0.147902] Advanced Linux Sound Architecture Driver Version 1.0.24. [ 0.149155] Switching to clocksource gp timer [ 0.167452] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host) [ 0.167633] musb-hdrc musb-hdrc.0: dma type: dma-cppi41 [ 0.167995] MUSB0 controller's USBSS revision = 4ea20800 [ 0.168030] musb0: Enabled SW babble control [ 0.169088] musb-hdrc musb-hdrc.0: USB OTG mode controller at e083c000 using DMA, IRQ 18 [ 0.169323] musb-hdrc musb-hdrc.1: dma type: dma-cppi41 [ 0.169698] MUSB1 controller's USBSS revision = 4ea20800 [ 0.169731] musb1: Enabled SW babble control [ 0.170207] musb-hdrc musb-hdrc.1: MUSB HDRC host driver [ 0.170310] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 [ 0.170442] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 0.170460] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.170476] usb usb1: Product: MUSB HDRC host driver [ 0.170488] usb usb1: Manufacturer: Linux 3.2.0-g2887c5a musb-hcd [ 0.170501] usb usb1: SerialNumber: musb-hdrc.1 [ 0.171474] hub 1-0:1.0: USB hub found [ 0.171507] hub 1-0:1.0: 1 port detected [ 0.172161] musb-hdrc musb-hdrc.1: USB Host mode controller at e083e800 using DMA, IRQ 19 [ 0.172627] NET: Registered protocol family 2 [ 0.172822] IP route cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.173140] TCP established hash table entries: 16384 (order: 5, 131072 bytes) [ 0.173497] TCP bind hash table entries: 16384 (order: 4, 65536 bytes) [ 0.173706] TCP: Hash tables configured (established 16384 bind 16384) [ 0.173720] TCP reno registered [ 0.173735] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.173762] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.173991] NET: Registered protocol family 1 [ 0.174282] RPC: Registered named UNIX socket transport module. [ 0.174297] RPC: Registered udp transport module. [ 0.174307] RPC: Registered tcp transport module. [ 0.174317] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.174564] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.194088] VFS: Disk quotas dquot_6.5.2 [ 0.194161] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.195050] msgmni has been set to 1001 [ 0.198503] alg: No test for stdrng (krng) [ 0.199279] io scheduler noop registered [ 0.199296] io scheduler deadline registered [ 0.199383] io scheduler cfq registered (default) [ 0.319777] omap_uart.0: ttyO0 at MMIO 0x44e09000 (irq = 72) is a OMAP UART0 [ 0.320361] omap_uart.1: ttyO1 at MMIO 0x48022000 (irq = 73) is a OMAP UART1 [ 0.320857] omap_uart.2: ttyO2 at MMIO 0x48024000 (irq = 74) is a OMAP UART2 [ 0.321325] omap_uart.3: ttyO3 at MMIO 0x481a6000 (irq = 44) is a OMAP UART3 [ 0.938669] console [ttyO3] enabled [ 0.942942] omap_uart.4: ttyO4 at MMIO 0x481a8000 (irq = 45) is a OMAP UART4 [ 0.950867] omap_uart.5: ttyO5 at MMIO 0x481aa000 (irq = 46) is a OMAP UART5 [ 0.959318] omap4_rng omap4_rng: OMAP4 Random Number Generator ver. 2.00 [ 0.977277] brd: module loaded [ 0.986344] loop: module loaded [ 0.989903] i2c-core: driver [tsl2550] using legacy suspend method [ 0.996390] i2c-core: driver [tsl2550] using legacy resume method [ 1.002873] at24 1-0057: 32768 byte 24c256 EEPROM, writable, 64 bytes/write [ 1.016830] Detected a carrier board for SMARC T335X Module.. [ 1.022706] Unknown CPLD version found [ 1.026867] at24 1-0050: 32768 byte 24c256 EEPROM, writable, 64 bytes/write [ 1.042104] Board name: SMARCT33 [ 1.045489] Board version: 00B0 [ 1.048779] The board is an Embedian SMARC T335X module. [ 1.056295] tps65217 1-0024: TPS65217 ID 0xe version 1.2 [ 1.064093] print_constraints: DCDC1: 900 <--> 1800 mV at 1500 mV [ 1.072873] print_constraints: DCDC2: 925 <--> 1325 mV at 1275 mV [ 1.081585] print_constraints: DCDC3: 925 <--> 1150 mV at 1125 mV [ 1.090230] print_constraints: LDO1: 1000 <--> 3300 mV at 1800 mV [ 1.098884] print_constraints: LDO2: 900 <--> 3300 mV at 3300 mV [ 1.107038] print_constraints: LDO3: 1800 mV [ 1.113891] print_constraints: LDO4: 1800 <--> 3300 mV at 3300 mV [ 1.121678] da8xx_lcdc.0: alias fck already exists [ 1.127310] da8xx_lcdc da8xx_lcdc.0: GLCD: Found PVI_PM070WL4 panel [ 1.152001] Console: switching to colour frame buffer device 100x30 [ 1.168250] davinci-mcasp.1: alias fck already exists [ 1.174504] omap_hsmmc.0: alias fck already exists [ 1.180032] omap_hsmmc.1: alias fck already exists [ 1.185609] d_can.0: alias fck already exists [ 1.190657] omap_i2c.2: alias fck already exists [ 1.195985] omap_i2c omap_i2c.2: bus 2 rev2.4.0 at 100 kHz [ 1.202229] omap_i2c.3: alias fck already exists [ 1.219244] omap_i2c omap_i2c.3: bus 3 rev2.4.0 at 100 kHz [ 1.229367] usb 1-1: new high-speed USB device number 2 using musb-hdrc [ 1.238459] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.245479] m25p80 spi1.0: unrecognized JEDEC id ffffff [ 1.253096] CAN device driver interface [ 1.257139] CAN bus driver for Bosch D_CAN controller 1.0 [ 1.263713] d_can d_can.0: device registered (irq=52, irq_obj=53) [ 1.319207] davinci_mdio davinci_mdio.0: davinci mdio revision 1.6 [ 1.325712] davinci_mdio davinci_mdio.0: detected phy mask fffffffc [ 1.333655] davinci_mdio.0: probed [ 1.337239] davinci_mdio davinci_mdio.0: phy[0]: device 0:00, driver SMSC LAN8710/LAN8720 [ 1.345882] davinci_mdio davinci_mdio.0: phy[1]: device 0:01, driver SMSC LAN8710/LAN8720 [ 1.355054] usbcore: registered new interface driver zd1201 [ 1.361157] usbcore: registered new interface driver cdc_ether [ 1.367464] usbcore: registered new interface driver cdc_eem [ 1.373813] usb 1-1: New USB device found, idVendor=0424, idProduct=2514 [ 1.380880] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 1.388761] usbcore: registered new interface driver dm9601 [ 1.394685] cdc_ncm: 04-Aug-2011 [ 1.398367] usbcore: registered new interface driver cdc_ncm [ 1.404337] Initializing USB Mass Storage driver... [ 1.410217] hub 1-1:1.0: USB hub found [ 1.414235] usbcore: registered new interface driver usb-storage [ 1.420580] USB Mass Storage support registered. [ 1.425546] hub 1-1:1.0: 4 ports detected [ 1.430829] usbcore: registered new interface driver usbserial [ 1.436965] usbserial: USB Serial Driver core [ 1.442011] USB Serial support registered for cp210x [ 1.447480] usbcore: registered new interface driver cp210x [ 1.453359] cp210x: v0.09:Silicon Labs CP210x RS232 serial adaptor driver [ 1.461005] mousedev: PS/2 mouse device common for all mice [ 1.472058] rtc-s35390a 1-0030: rtc core: registered rtc-s35390a as rtc0 [ 1.479338] i2c /dev entries driver [ 1.483970] Linux video capture interface: v2.00 [ 1.489239] usbcore: registered new interface driver uvcvideo [ 1.495284] USB Video Class driver (1.1.1) [ 1.503855] OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 1.511758] cpuidle: using governor ladder [ 1.516645] cpuidle: using governor menu [ 1.524630] omap4_aes_mod_init: loading AM33X AES driver [ 1.530376] omap4-aes omap4-aes: AM33X AES hw accel rev: 3.02 [ 1.537278] omap4_aes_probe: probe() done [ 1.542073] omap4_sham_mod_init: loading AM33X SHA/MD5 driver [ 1.548256] omap4-sham omap4-sham: AM33X SHA/MD5 hw accel rev: 4.03 [ 1.563770] omap4_sham_probe: probe() done [ 1.574335] usbcore: registered new interface driver usbhid [ 1.580230] usbhid: USB HID core driver [ 1.585025] tiadc tiadc: attached adc driver [ 1.590403] usbcore: registered new interface driver snd-usb-audio [ 1.602010] asoc: tlv320aic3x-hifi <-> davinci-mcasp.1 mapping ok [ 1.610036] ALSA device list: [ 1.613171] #0: TLV320AIC3X SOUND CARD [ 1.617283] oprofile: hardware counters not available [ 1.622607] oprofile: using timer interrupt. [ 1.627118] nf_conntrack version 0.5.0 (8015 buckets, 32060 max) [ 1.634028] ip_tables: (C) 2000-2006 Netfilter Core Team [ 1.639791] TCP cubic registered [ 1.643188] NET: Registered protocol family 17 [ 1.647863] can: controller area network core (rev 20090105 abi 8) [ 1.654482] NET: Registered protocol family 29 [ 1.659164] can: raw protocol (rev 20090105) [ 1.663665] can: broadcast manager protocol (rev 20090105 t) [ 1.669664] Registering the dns_resolver key type [ 1.674682] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 1.682760] ThumbEE CPU extension supported. [ 1.687308] mux: Failed to setup hwmod io irq -22 [ 1.692951] Power Management for AM33XX family [ 1.697833] Trying to load am335x-pm-firmware.bin (60 secs timeout) [ 1.704573] Copied the M3 firmware to UMEM [ 1.708955] Cortex M3 Firmware Version = 0x181 [ 1.719487] clock: disabling unused clocks to save power [ 1.738047] mmc0: new high speed SDHC card at address 0002 [ 1.744636] mmcblk0: mmc0:0002 00000 3.81 GiB [ 1.751089] mmcblk0: p1 p2 [ 1.757014] Detected MACID=1c:ba:8c:d6:53:3 [ 1.762635] cpsw: Detected MACID = 1c:ba:8c:d6:53:05 [ 1.769867] rtc-s35390a 1-0030: setting system clock to 2014-03-23 09:45:52 UTC (1395567952) [ 1.794862] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 1.803487] VFS: Mounted root (ext4 filesystem) on device 179:2. [ 1.810316] Freeing init memory: 236K [ 1.814521] usb 1-1.1: new full-speed USB device number 3 using musb-hdrc [ 1.854852] mmc1: new high speed MMC card at address 0001 [ 1.861912] mmcblk1: mmc1:0001 M4G1YC 3.64 GiB [ 1.867471] mmcblk1boot0: mmc1:0001 M4G1YC partition 1 2.00 MiB [ 1.874200] mmcblk1boot1: mmc1:0001 M4G1YC partition 2 2.00 MiB [ 1.883042] mmcblk1: unknown partition table [ 1.889992] mmcblk1boot1: unknown partition table [ 1.898184] mmcblk1boot0: unknown partition table [ 1.920854] usb 1-1.1: New USB device found, idVendor=10c4, idProduct=ea71 [ 1.928113] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=7 [ 1.935831] usb 1-1.1: Product: CP2108 Quad USB to UART Bridge Controller [ 1.942981] usb 1-1.1: Manufacturer: Silicon Labs [ 1.947929] usb 1-1.1: SerialNumber: 66A3D0B1208B7C9311E366EF841921B [ 1.958173] cp210x 1-1.1:1.0: cp210x converter detected INIT: version 2.88 booting[ 2.039327] usb 1-1.1: reset full-speed USB device number 3 using musb-hdrc [ 2.161669] usb 1-1.1: cp210x converter now attached to ttyUSB0 [ 2.170333] cp210x 1-1.1:1.1: cp210x converter detected [ 2.177148] cp210x ttyUSB0: cp210x converter now disconnected from ttyUSB0 [ 2.185767] cp210x 1-1.1:1.0: device disconnected [ 2.269639] usb 1-1.1: reset full-speed USB device number 3 using musb-hdrc [ 2.390118] cp210x 1-1.1:1.0: cp210x converter detected Starting udev [ 2.489381] usb 1-1.1: reset full-speed USB device number 3 using musb-hdrc [ 2.610667] usb 1-1.1: cp210x converter now attached to ttyUSB0 [ 2.633853] usb 1-1.1: cp210x converter now attached to ttyUSB1 [ 2.642904] cp210x 1-1.1:1.2: cp210x converter detected [ 2.648971] cp210x ttyUSB0: cp210x converter now disconnected from ttyUSB0 [ 2.656314] cp210x 1-1.1:1.0: device disconnected [ 2.661676] cp210x ttyUSB1: cp210x converter now disconnected from ttyUSB1 [ 2.668938] cp210x 1-1.1:1.1: device disconnected [ 2.759418] usb 1-1.1: reset full-speed USB device number 3 using musb-hdrc [ 2.950707] cp210x 1-1.1:1.1: cp210x converter detected [ 3.169390] usb 1-1.1: reset full-speed USB device number 3 using musb-hdrc [ 3.460231] cp210x 1-1.1:1.0: cp210x converter detected [ 3.699428] usb 1-1.1: reset full-speed USB device number 3 using musb-hdrc [ 3.880751] usb 1-1.1: cp210x converter now attached to ttyUSB0 [ 4.181693] usb 1-1.1: cp210x converter now attached to ttyUSB1 [ 4.188419] cp210x ttyUSB0: cp210x converter now disconnected from ttyUSB0 [ 4.195761] cp210x 1-1.1:1.0: device disconnected [ 4.200863] cp210x 1-1.1:1.0: cp210x converter detected [ 4.206774] cp210x ttyUSB1: cp210x converter now disconnected from ttyUSB1 [ 4.214078] cp210x 1-1.1:1.1: device disconnected [ 5.609393] usb 1-1.1: reset full-speed USB device number 3 using musb-hdrc [ 5.790312] cp210x 1-1.1:1.1: cp210x converter detected [ 5.909403] usb 1-1.1: reset full-speed USB device number 3 using musb-hdrc [ 6.090736] usb 1-1.1: cp210x converter now attached to ttyUSB0 [ 6.177432] usb 1-1.1: cp210x converter now attached to ttyUSB1 [ 6.261321] usb 1-1.1: cp210x converter now attached to ttyUSB2 [ 6.362588] cp210x 1-1.1:1.3: cp210x converter detected [ 6.368651] cp210x ttyUSB1: cp210x converter now disconnected from ttyUSB1 [ 6.376001] cp210x 1-1.1:1.0: device disconnected [ 6.381386] cp210x ttyUSB0: cp210x converter now disconnected from ttyUSB0 [ 6.388661] cp210x 1-1.1:1.1: device disconnected [ 6.394017] cp210x ttyUSB2: cp210x converter now disconnected from ttyUSB2 [ 6.401315] cp210x 1-1.1:1.2: device disconnected [ 6.639405] usb 1-1.1: reset full-speed USB device number 3 using musb-hdrc [ 6.800318] cp210x 1-1.1:1.2: cp210x converter detected [ 6.909453] usb 1-1.1: reset full-speed USB device number 3 using musb-hdrc [ 7.040481] cp210x 1-1.1:1.1: cp210x converter detected [ 7.129330] usb 1-1.1: reset full-speed USB device number 3 using musb-hdrc [ 7.230098] cp210x 1-1.1:1.0: cp210x converter detected [ 7.329272] usb 1-1.1: reset full-speed USB device number 3 using musb-hdrc [ 7.450424] usb 1-1.1: cp210x converter now attached to ttyUSB0 [ 7.457158] usb 1-1.1: cp210x converter now attached to ttyUSB1 [ 7.463882] cp210x ttyUSB0: cp210x converter now disconnected from ttyUSB0 [ 7.471187] cp210x 1-1.1:1.0: device disconnected [ 7.476262] cp210x 1-1.1:1.0: cp210x converter detected [ 7.482189] cp210x ttyUSB1: cp210x converter now disconnected from ttyUSB1 [ 7.489491] cp210x 1-1.1:1.1: device disconnected [ 7.589285] usb 1-1.1: reset full-speed USB device number 3 using musb-hdrc [ 7.709976] cp210x 1-1.1:1.1: cp210x converter detected [ 7.809266] usb 1-1.1: reset full-speed USB device number 3 using musb-hdrc [ 7.930408] usb 1-1.1: cp210x converter now attached to ttyUSB0 [ 7.937486] usb 1-1.1: cp210x converter now attached to ttyUSB1 [ 7.944449] usb 1-1.1: cp210x converter now attached to ttyUSB2 [ 7.951177] cp210x ttyUSB0: cp210x converter now disconnected from ttyUSB0 [ 7.958465] cp210x 1-1.1:1.1: device disconnected [ 7.963551] cp210x 1-1.1:1.1: cp210x converter detected [ 7.969457] cp210x ttyUSB1: cp210x converter now disconnected from ttyUSB1 [ 7.976739] cp210x 1-1.1:1.0: device disconnected [ 7.982080] cp210x ttyUSB2: cp210x converter now disconnected from ttyUSB2 [ 7.989370] cp210x 1-1.1:1.2: device disconnected [ 8.089289] usb 1-1.1: reset full-speed USB device number 3 using musb-hdrc [ 8.209991] cp210x 1-1.1:1.2: cp210x converter detected [ 8.309273] usb 1-1.1: reset full-speed USB device number 3 using musb-hdrc [ 8.429932] cp210x 1-1.1:1.0: cp210x converter detected [ 8.529268] usb 1-1.1: reset full-speed USB device number 3 using musb-hdrc [ 8.650395] usb 1-1.1: cp210x converter now attached to ttyUSB0 [ 8.657091] usb 1-1.1: cp210x converter now attached to ttyUSB1 [ 8.663807] cp210x ttyUSB0: cp210x converter now disconnected from ttyUSB0 [ 8.671114] cp210x 1-1.1:1.0: device disconnected [ 8.676176] cp210x 1-1.1:1.0: cp210x converter detected [ 8.682100] cp210x ttyUSB1: cp210x converter now disconnected from ttyUSB1 [ 8.689401] cp210x 1-1.1:1.2: device disconnected [ 8.789283] usb 1-1.1: reset full-speed USB device number 3 using musb-hdrc [ 8.909986] cp210x 1-1.1:1.2: cp210x converter detected [ 9.009269] usb 1-1.1: reset full-speed USB device number 3 using musb-hdrc [ 9.120404] usb 1-1.1: cp210x converter now attached to ttyUSB0 [ 9.127113] usb 1-1.1: cp210x converter now attached to ttyUSB1 [ 9.137072] usb 1-1.1: cp210x converter now attached to ttyUSB2 [ 9.143818] cp210x ttyUSB1: cp210x converter now disconnected from ttyUSB1 [ 9.151128] cp210x 1-1.1:1.0: device disconnected [ 9.156194] cp210x 1-1.1:1.0: cp210x converter detected [ 9.162111] cp210x ttyUSB2: cp210x converter now disconnected from ttyUSB2 [ 9.169403] cp210x 1-1.1:1.1: device disconnected [ 9.174739] cp210x ttyUSB0: cp210x converter now disconnected from ttyUSB0 [ 9.182035] cp210x 1-1.1:1.2: device disconnected [ 9.269286] usb 1-1.1: reset full-speed USB device number 3 using musb-hdrc [ 9.389955] cp210x 1-1.1:1.2: cp210x converter detected [ 9.489266] usb 1-1.1: reset full-speed USB device number 3 using musb-hdrc [ 9.609920] cp210x 1-1.1:1.1: cp210x converter detected [ 9.709273] usb 1-1.1: reset full-speed USB device number 3 using musb-hdrc [ 9.830379] usb 1-1.1: cp210x converter now attached to ttyUSB0 [ 9.837486] usb 1-1.1: cp210x converter now attached to ttyUSB1 [ 9.844218] cp210x ttyUSB0: cp210x converter now disconnected from ttyUSB0 [ 9.851521] cp210x 1-1.1:1.1: device disconnected [ 9.856584] cp210x 1-1.1:1.1: cp210x converter detected [ 9.862516] cp210x ttyUSB1: cp210x converter now disconnected from ttyUSB1 [ 9.869816] cp210x 1-1.1:1.2: device disconnected [ 9.969289] usb 1-1.1: reset full-speed USB device number 3 using musb-hdrc [ 10.089942] cp210x 1-1.1:1.2: cp210x converter detected [ 10.189259] usb 1-1.1: reset full-speed USB device number 3 using musb-hdrc [ 10.310437] usb 1-1.1: cp210x converter now attached to ttyUSB0 [ 10.317543] usb 1-1.1: cp210x converter now attached to ttyUSB1 [ 10.324540] usb 1-1.1: cp210x converter now attached to ttyUSB2 [ 10.331512] usb 1-1.1: cp210x converter now attached to ttyUSB3 Starting Bootlog daemon: bootlogd.[ 12.275440] EXT4-fs (mmcblk0p2): re-mounted. Opts: user_xattr,barrier=1,data=ordered ALSA: Restoring mixer settings... INIT: Entering runlevel: 5 Starting system message bus: dbus.Starting Dropbear SSH server: Starting network benchmark server: netserver.Configuring network interfaces... [ 13.355564] net eth0: CPSW phy found : id is : 0x7c0f1 udhcpc (v1.20.2) startedSending discover...[ 16.349793] PHY: 0:00 - Link is Up - 100/Full Sending discover...Sending select for 192.168.1.67...Lease of 192.168.1.67 obtained, lease time 86400/etc/udhcpc.d/50default: Adding DNS 192.168.1.254done.Starting ntpd: doneStarting syslogd/klogd: doneStarting thttpd.Starting Lighttpd Web Server: lighttpd.2014-03-23 09:46:07: (log.c.166) server started Starting crond: OK/Starting Matrix GUI application.[ 21.078003] gadget: Mass Storage Function, version: 2009/09/11 [ 21.084330] gadget: Number of LUNs=1 [ 21.088193] lun0: LUN: removable file: /dev/mmcblk0p1 [ 21.093657] gadget: Mass Storage Gadget, version: 2009/09/11 [ 21.099724] gadget: userspace failed to provide iSerialNumber [ 21.105890] gadget: g_mass_storage ready [ 21.110151] musb-hdrc musb-hdrc.0: MUSB HDRC host driver [ 21.115801] musb-hdrc musb-hdrc.0: new USB bus registered, assigned bus number 2 [ 21.123726] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 21.130892] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 21.138495] usb usb2: Product: MUSB HDRC host driver [ 21.143728] usb usb2: Manufacturer: Linux 3.2.0-g2887c5a musb-hcd [ 21.150148] usb usb2: SerialNumber: musb-hdrc.0 [ 21.155553] hub 2-0:1.0: USB hub found [ 21.159544] hub 2-0:1.0: 1 port detected [9;0][?33l[?25l[?1c ******************************************************************************************************************************NOTICE: This file system contains the followin GPLv3 packages: binutils-symlinks binutils gdbserver rsyslogIf you do not wish to distribute GPLv3 components please removethe above packages prior to distribution. This can be done usingthe opkg remove command. i.e.: opkg remove Where is the name printed in the list aboveNOTE: If the package is a dependency of another package you will be notified of the dependent packages. You should use the --force-removal-of-dependent-packages option to also remove the dependent packages as well******************************************************************************************************************************Stopping Bootlog daemon: bootlogd. _____ _____ _ _ | _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_ | | _| .'| . | . | | __| _| . | | | -_| _| _| |__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_| |___| |___| Arago Project http://arago-project.org smarct335x ttyO3 Arago 2013.05 smarct335x ttyO3 smarct335x login: root root@smarct335x:~#